Maytag Top Loading Washer Lid Lock Light Is Blinking

Whirlpool Cabrio Washing Machine Stops At Start Of Spin – Lid Lock Light Flashing. This is very important since most complaints start with the lid lock on and blinking, or the unit will not start and spin. – When in diagnostics the codes are F7 E1, F7 E5, or motor speed codes, then chances are it is a motor, capacitor, or shifter related issue. The lid lock light on VMW washers, made by Whirlpool, Kenmore and Maytag, will flash whenever there is a. Hey everyone, I am working on a Kenmore top load washer, model no: 13 that will shut down and the lid lock light will blink. The Lid Lock Light will flash if Lid Lock has not moved into the Lock Position, the Lock Motor can not be powered, or the Lid is not closed completely due to interference. Some models will lock immediately, while others will not lock until after the wash cycle has started.

• Maytag Top Loading Washer Lid Lock Light Is Blinking Yellow
• Maytag Washer Spin Light Blinking

After replacing the lid lock switch for the problem machine would not spin and lid lock light flashed,we still have a big problem. After starting a small load (2 towel) the machine goes into sensing mode as it should, lid locks, unlocks and re locks as it should lid light blinks and nothing happens. After about 5 minutes the machine starts to fill with water with out sensing. Too much water is going in for 2 towels. I then shut the power off, unplug and then restart to drain/spin which it does but at the end of the cycle the lid locks light starts to blink again and nothing happens.

I shut the power off unplug to unlock the lid and open the machine. The towels are spun and no water is in the machine. What could be the problem with this 4 year old Sears He model 0. It is obviously not the lid lock as suggested to us.

Very disappointed in this machine. Can you help us. We have a series 400 Kenmore washing machine. Initially the problem began with it not draining the water completely during the drain cycle at the end. I would run the drain cycle again and it was all fine.

Then it started having the lid lock flashing continuosly and would not spin to dry the clothes. Then it couldnt sense the clothes level and would do nothing with the lid lock coming on and off and then just flashing. The machine seemed to be comletely confused. So we ordered a new control board but that didnt help either. So doing more digging online we found someone with a similar problem who said that it was the actuator that needed replacing. Said that even if lid lock is flashing its not a problem with that part.

We installed the actuator today and the machine works well. Hope this helps someone else. Took my husband five minutes to change it.

COPYRIGHT 2018 -www.ApplianceRepairQuestions.com -Ask Any Appliance Repair Question And Get FREE Expert Answers Fast.We specialize in troubleshooting and repairing GE, LG, Maytag, Whirlpool, Frigidaire,Bosch, Amana, Samsung, Hotpoint, Viking, Kenmore, Jenn-Air, KitchenAid, Electrolux,Miele,Asko, Wolf, Sub-Zero, Fisher & Paykel, Tappan, and many more appliance brands. We can assist you with any type of dishwasher, washing machine, refrigerator, or clothes dryer repair.DIY Appliance Repair - Online Appliance Help To Fix And Repair Your Broken Appliance - Ask a Question, Get An Answer, Do It Yourself, Save Money.

When I try to start a load, it locks the lid, tries to sense, but doesn't spin even a little. It will unlock (and stays that way for almost 30 secs which is longer than before) and then it locks again and the 'lid locked' light starts flashing.

It does this on all load options. I know the lid sensor is notorious for needing replaced, but it does lock and stays locked.

Maytag Top Loading Washer Lid Lock Light Is Blinking Yellow

Maytag Washer Spin Light Blinking

I have to cancel the cycle and then unplug the machine and plug it back in to get the lid to unlock.Any ideas of where do I start?